APC Systems for Buses: Sensor Types, Accuracy and What to Specify
How automatic passenger counting (APC) sensors work on buses, what affects counting accuracy, how to test it, and what to ask a supplier before you buy.
Short answer: an automatic passenger counting (APC) system uses a sensor above each bus door to count people getting on and off. The best results come from overhead sensors that see depth and direction, mounted and calibrated for each door, and checked against manual counts before the data is trusted for revenue decisions.
What does an APC system include?
- A sensor above each door, facing down at the doorway.
- Processing in the sensor or an onboard unit, which turns movement into counts.
- GPS, so each count is tied to a stop and a time.
- A connection to the fleet platform, for live occupancy and reports.
Which sensor types are used?
- Infrared beams: a person breaks one beam, then another, which gives direction. Cheap, but easily confused when two people pass together.
- Stereo or 3D depth sensors: two lenses or a time-of-flight sensor measure height, so the system can tell people apart from bags and see who is moving which way.
- AI vision sensors: an overhead camera with a model trained to detect heads and shoulders from above, tracking each person through the doorway.
Overhead depth and AI sensors are the usual choice for buses, because doorways are crowded and passengers rarely move one at a time.
What affects counting accuracy?
- Crowding at the door, especially on city routes at peak hours.
- People who hesitate, step back down or stand on the steps.
- Children, luggage and prams, which a simple sensor may miss or count as a person.
- Mounting height and angle, which must match the door the sensor was set up for.
- Lighting, from bright sun at the door to dark night stops.
- Door width, where two passengers can board side by side.
How do you check that the counts are right?
- Pick a sample of trips on different routes and times of day.
- Count passengers manually, or from cabin video, at every stop.
- Compare the manual count with the APC count, stop by stop and for the whole trip.
- Adjust mounting or settings where the gap is large, then test again.
- Repeat the check from time to time, and after any door or body work on the bus.
Ask the supplier how they measure accuracy and whether they will run this check on your buses during the pilot. A figure measured in a lab doorway may not hold on a crowded city bus.
What can operators do with APC data?
- Live occupancy: know how full each bus is while it is running.
- Stop-wise boarding and alighting: find the busiest stops and the empty ones.
- Revenue checks: compare passengers counted with tickets issued on each trip. See how counting helps find revenue leakage.
- Timetable and route planning: add or remove trips based on measured demand.
What should an operator specify?
- One sensor per door in use, including the rear door on city buses.
- Direction-aware counting, with boarding and alighting recorded separately.
- GPS stop tagging for every count.
- Offline storage, so counts are not lost where there is no signal.
- Privacy by design: an overhead view that counts people without identifying faces.
- Export or integration with your ticketing reports.
- An accuracy test on your own buses before full rollout.
For the basics, read how automatic passenger counting works. AirFi supplies and installs automatic passenger counting for buses, linked to GPS stops on the fleet dashboard. Talk to our team about a counting pilot.
Frequently asked questions
What is an APC system in a bus?
An automatic passenger counting (APC) system uses a sensor above each door to count passengers boarding and alighting, tagged with the GPS stop, so operators can see occupancy and stop-wise demand.
How accurate is automatic passenger counting?
Accuracy depends on the sensor type, mounting, crowding and lighting. Overhead depth or AI sensors handle crowded doorways better than simple beams. Check accuracy on your own buses by comparing APC counts with manual counts.
Does a passenger counter record passengers’ faces?
An overhead counting sensor looks straight down at the doorway, so it counts heads and shoulders rather than identifying people.
Can APC data detect ticket revenue leakage?
It can highlight it. When the passenger count on a trip is well above the tickets issued, the gap is worth investigating.
Related solutions
Planning a smarter, safer fleet?
Talk to AirFi →